Plugs a channel into a mixer.

BOOL BASS_Mixer_StreamAddChannel(
    HSTREAM handle,
    DWORD channel,
    DWORD flags


handleThe mixer handle.
channelThe handle of the channel to plug into the mixer... a HMUSIC, HSTREAM or HRECORD.
flagsAny combination of these flags.
BASS_MIXER_CHAN_BUFFERBuffer the sample data, for use by BASS_Mixer_ChannelGetData and BASS_Mixer_ChannelGetLevel and BASS_Mixer_ChannelGetLevelEx. This increases memory requirements, so should not be enabled needlessly. The size of the buffer can be controlled via the BASS_CONFIG_MIXER_BUFFER config option.
BASS_MIXER_CHAN_DOWNMIXIf the source has more channels than the mixer output (and the mixer is stereo or mono), then a channel matrix is created, initialized with the appropriate downmixing matrix (for up to 8 channels). Note the source data is assumed to follow the standard channel ordering, as described in the STREAMPROC documentation.
BASS_MIXER_CHAN_LIMITLimit the mixer processing to the amount of data available from this source, while the source is active (not ended). If the source stalls, then the mixer will too, rather than continuing to mix other sources, as it would normally do. This flag can only be applied to one source per mixer, so it will automatically be removed from any other source of the same mixer.
BASS_MIXER_CHAN_MATRIXCreates a channel matrix, allowing the source's channels to be sent to any of the mixer output channels, at any levels. The matrix can be retrieved and modified via the BASS_Mixer_ChannelGetMatrix and BASS_Mixer_ChannelSetMatrix functions. The matrix will initially contain a one-to-one mapping, eg. left out = left in, right out = right in, etc.
BASS_MIXER_CHAN_NORAMPINDo not ramp-in the start, including after seeking (BASS_Mixer_ChannelSetPosition). This is useful for gap-less playback, where a source channel is intended to seamlessly follow another. This does not affect volume and pan changes, which are always ramped.
BASS_MIXER_CHAN_PAUSEPause processing of the source. Use BASS_Mixer_ChannelFlags to resume processing.
BASS_STREAM_AUTOFREEAutomatically free the source channel when it ends. This allows you to add a channel to a mixer and forget about it, as it will automatically be freed when it has reached the end, or when the source is removed from the mixer or when the mixer is freed. When the mixer reaches the end of it, the source will be freed asynchronously (in another thread) to avoid delaying the mixer's other processing.
BASS_SPEAKER_xxxSpeaker assignment flags. If matrix mixing is enabled then the matrix will be initialized to place the source on the requested speaker(s), with downmixing also applied if the BASS_MIXER_CHAN_DOWNMIX flag is specified. The BASS_Init BASS_DEVICE_NOSPEAKER flag has effect here.

Return value

If successful, then TRUE is returned, else FALSE is returned. Use BASS_ErrorGetCode to get the error code.

Error codes

BASS_ERROR_HANDLEAt least one of handle and channel is not valid.
BASS_ERROR_DECODEchannel is not a decoding channel.
BASS_ERROR_ALREADYchannel is already plugged into a mixer. It must be unplugged first.
BASS_ERROR_SPEAKERThe mixer does not support the requested speaker(s), or you are attempting to assign a stereo stream to a mono speaker.


Internally, a mixer will use the BASS_ChannelGetData function to get data from its source channels. That means that the source channels must be decoding channels (not using a RECORDPROC in the case of a recording channel). Plugging a channel into more than one mixer at a time is not possible because the mixers would be taking data away from each other. An advantage of this is that there is no need for a mixer's handle to be provided with the channel functions. It is actually possible to plug a channel into multiple mixers via the use of splitter streams.

Channels are "unplugged" using the BASS_Mixer_ChannelRemove function. Channels are also automatically unplugged when they are freed.

When mixing a channel, the mixer makes use of the channel's freq/volume/pan attributes, as set with BASS_ChannelSetAttribute. The BASS_CONFIG_CURVE_VOL and BASS_CONFIG_CURVE_PAN config option settings are also used. The channel's pan attribute has no effect when matrix mixing is enabled; panning can be applied in the matrix instead then.

If a multi-channel stream has more channels than the mixer output, the extra channels will be discarded. For example, if a 5.1 stream is plugged into a stereo mixer, only the front-left/right channels will be retained. That is unless matrix mixing is used.

The mixer processing is performed in floating-point, so it makes sense (for both quality and efficiency reasons) for the source channels to be floating-point too, though they do not have to be. It is also more efficient if the source channels have the same sample rate as the mixer output because no sample rate conversion is required then. When sample rate conversion is required, windowed sinc interpolation is used and the source's BASS_ATTRIB_SRC attribute determines how many points/samples are used in that, as follows: 0 (or below) = 4 points, 1 = 8 points, 2 = 16 points, 3 = 32 points, 4 = 64 points, 5 = 128 points, 6 (or above) = 256 points. 8 points are used if the BASS_ATTRIB_SRC attribute is unavailable (old BASS version). A higher number of points results in better sound quality (less aliasing and smaller transition band in the low-pass filter), but also higher CPU usage.


The sample rate conversion processing is limited to 128 points on iOS and Android. The mixer processing is performed in fixed-point rather than floating-point on some platforms/architectures, as indicated by the BASS_CONFIG_FLOAT value.

See also

BASS_Mixer_ChannelFlags, BASS_Mixer_ChannelGetLevel, BASS_Mixer_ChannelGetMixer, BASS_Mixer_ChannelGetPosition, BASS_Mixer_ChannelRemove, BASS_Mixer_ChannelSetMatrix, BASS_Mixer_ChannelSetPosition, BASS_Mixer_StreamAddChannelEx, BASS_Mixer_StreamCreate